Home Improvement

What does code Ld mean on Maytag?

Long DrainLong Drain: this could indicate that the washing machine is taking longer than 5 minutes to drain out enough water to reset the water pressure switch.

Why does my washer keep saying LD?

If Ld (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub.

How do you fix a OL code on a Maytag washer?

If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent. Close lid and press START/PAUSE.

What does Ld mean in code?

ld (Load Doubleword) instruction.

How do you unclog a Maytag Bravos washing machine?

You can see everything all you need to do to take the pump off and check is remove. These two red clamps. This is your intake that your output. So you loosen those up.

How do you drain a Whirlpool washing machine?

Find the “Pause/Cancel” button on the control panel. Press this button twice to drain the washer. Press the “Power” button and rotate the cycle selection knob to “Drain and Spin” to remove the remaining water from the load.

How do you reset the code LD on a top Whirlpool Cabrio Platinum?

Try the Cabrio Reset Procedure



Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.

Why does my washer keep saying OL?

First, OL stands for “Overload”, so in other words, the washer thinks the tub is too hard to move because it’s overloaded and the motor is struggling or the unit is way out of balance causing the washer to struggle. The most common problem is a nut below the inner tub that needs to “float”.

How do I reset my top load washer?

Motor Reset Procedure:

  1. Unplug the washer for 1 minute from the electrical outlet.
  2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
  3. The motor has now been reset and is ready for you to start a cycle.


Why does my Maytag washer says UL?

If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.

What does Ld mean on Maytag Bravos?

Long Drain

mamajtown, Ld code is for Long Drain: this could indicate that the washing machine is taking longer than 5 minutes to drain out enough water to reset the water pressure switch.

How do I know if my washing machine drain hose is clogged?

An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump. If the hose is worn or badly kinked, replacing the hose may improve the ability of the machine to pump water.

Why won’t my Maytag washer drain and spin?

Make sure that the drain hose is not kinked or clogged. Straighten the hose for adequate water flow. Remove any blockage from the drain hose, drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose.

What causes a washing machine not to drain and spin?

If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.

How do I reset my Maytag washer?

The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.

How do you fix a Maytag washer that will not spin?

Or simply tighten up the nut on the splutch. If that is simply loose if you need to remove the belt. Simply pull the belt away from the washer.

How do I get my Maytag washer to spin?

Here are some tips you can use yourself to find out why your Maytag washer won’t spin:

  1. Tip #1: Check for Jammed Clothes. One common cause why a Maytag top load washer won’t spin is due to an uneven load or jammed clothing. …
  2. Tip #2: Inspect Lid Switch. …
  3. Tip #3: Check Drive Belt.


How do I fix the spin cycle on my washing machine?

No tools are required. Please follow these three easy steps. 1 power down the unit by unplugging the washer from the outlet. To wait approximately one minute and plug the washer back into the outlet.

Why is the spin cycle not working?

If the spin cycle doesn’t work, the belt may be loose or broken. Tighten or replace the belt. 2. Check the lid switch and the tab on the lid that strikes it.

How do you unclog a washing machine drain?

To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it. Yes?

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.

How long does it take for washing machine to reset?

A power cycle is done by unplugging the washing machine or turning it off at the circuit breaker. You should wait a minimum of five minutes before plugging the machine back in again.

How do I reset my Maytag Bravos XL washer to factory settings?

Turn the Cycle Selector knob counterclockwise or left (all the way around) once. Next, turn the knob clockwise (right) – Go three clicks clockwise (count one… two… three as you turn the dial clockwise).

How do I reset my Maytag Centennial washer?

How to reset Maytag Centennial washer (step by step) Simply unplug your washer for about 15-20 seconds then plug the machine back in. You can also reset the breakers again for anything between 20 seconds to 1 minute. This resets the main board and it might clear the error making the washer fail to function properly.

Is there a reset button on a Maytag?

The Maytag washer doesn’t have a reset button. If you need the reset button, you have to use the ‘Power/Cancel’ button. Push it to stop the current cycle. Select a new cycle and then press ‘Start/Pause.

How do I reset my Maytag control board?

Reset power to the product:

  1. Power unit down by turning off the circuit breaker(s) or unpluging the product for 5 – 10 minutes.
  2. Power unit up by turning on the circuit breaker(s) or plugging the product back in.
  3. Ensure the cooling function is turned on.
  4. Test the control panel functionality.


Adblock
detector