Home Improvement

How do you change the spool on a WORX trimmer?

How do I change the line on my Worx trimmer?

You're just going to push your line into the side of the main body and push it into place. And you're going to release the line.

How do you remove the trimmer spool?

To remove the old spool press the tabs on the spool cover and pull the cover straight off next lift the spool out of the hub.

How do you reload a spool trimmer?

Hold the outside of the head and then turn the center knob in the direction of the arrows. Just trim the lines. And that's all there is to fill in the easy spool head on the small trimmer.

How do you remove a spool retainer?

You can push those tabs through from the outside of the spindle. And then pull the retainer out of the spindle.

What size string does a Worx trimmer use?

approximately 0.065”

The diameter of this line is approximately 0.065”. The line is pre-wound on spools specially designed to work on Worx 20V and 32V battery operated trimmers.

How does Worx command feed work?

Try flex line it's the toughest most durable trimmer line we've ever offered. So you'll trim an edge for longer and works includes free factory well in schools for lights just pop out the cartridge.

How do you replace an electric trimmer head?

Remove the nut on the inside center of the trimmer head housing that secures the housing to the trimmer drive shaft with a socket wrench. Pull the trimmer head housing away from the trimmer. Place the new trimmer head housing over the drive shaft and secure with the retaining washer and nut.

How do you remove trimmer blades?

And set the screws in a safe. Place. Now loosen the two screws on the back of the blade set a quarter turn counterclockwise. Each do not completely remove these two screws with the screws loosened.

How do you rewind a dual line trimmer?

This string right you stick it in. And you stick it in so you go ahead and stick both of those in alright. And then you might want to try to avoid kinks. And stuff. And go ahead and you start winding.

How do you remove a stuck bump knob?

See that then what you do is grab these grab some pliers that are skinny enough to get in there. And get around that axle that you can see squeeze it tightly and then you can just twist the cap.

How do you take the spool cap off a Ryobi trimmer?

Depress the two retaining tabs to release the lower trimmer head housing. Lift the spool out of the housing. And detach the bump knob. Remove the trimmer line from the spool.

How do you remove the spool from a Homelite trimmer?

But don't tighten it too much because you can bend the metal casing. The first thing you need to do is to remove the knob. Completely.

What is a flower guard on a grass trimmer?

About this product



With a telescopic shaft you can adjust the height to suit your needs. The flower guard allows you to cut right up to your flowerbeds without cutting the flowers inside. At a weight of just 2.75kg it is easy to store in your shed, garage or outbuilding, as it can easily be hung on a hook.

Why is my Worx trimmer not working?

If the replacement battery doesn’t work, the charging station may need to be replaced. Plug the charged battery into the trimmer. Press in the lock button, on the side of the rear handle, and depress the trigger. If the lock button doesn’t work, the head won’t spin, so the lock button will need to be replaced.

How do you install Yardworks grass trimmer strings?

How to Install a Yardworks Grass Trimmer String

  1. Grip the cutter knob and turn it counter-clockwise to remove it. Remove any excess yard debris.
  2. Remove any excess line still wrapped around the previous spool. …
  3. Insert the spring within the replacement spool. …
  4. Pull the replacement line through the slots of the outer hub.


How do you replace an electric trimmer head?

Remove the nut on the inside center of the trimmer head housing that secures the housing to the trimmer drive shaft with a socket wrench. Pull the trimmer head housing away from the trimmer. Place the new trimmer head housing over the drive shaft and secure with the retaining washer and nut.

How do you rewind a dual line trimmer?

This string right you stick it in. And you stick it in so you go ahead and stick both of those in alright. And then you might want to try to avoid kinks. And stuff. And go ahead and you start winding.

Why does my strimmer wire keep snapping?

Usually this is the result of the cutting head being taken too close to objects, e.g. garden stones, paving edges, walls etc. The cutting line must be allowed to rotate freely and the correct diameter and type of line should be used.

How do you install strimmer wire?

Even though you might have a different brand most string trimmers work generally the same. You can either pinch off the cap like this one or sometimes it's a pinch and twist or just a twist.

How do I stop my strimmer line from sticking?

So grab your WD-40 can and spray all of your line until it’s soaked. This stops the line from binding together and the line should subsequently work just fine. A silicone spray would also be an excellent option and tends to catch less dust than WD-40.

How does string trimmer auto feed work?

The Automatic Feed Spool (AFS) is the technologically advanced line feed system found on Black & Decker string trimmer products. Using centrifugal force, the system monitors the amount of line being used and feeds more line automatically as the cutting line shortens.

How do I fix the auto feed trimmer?

The cap allows you to feed more line when you tap it on the ground. If the cap is damaged or worn it can malfunction causing wine not to advance to inspect the cap remove it and clean any debris.

How do you bump feed a line trimmer?

And we just bump this on the ground like so then the line will move out around about 10 millimeters each time we bump it but the head of the machine must be rotating firmly.

How do you feed line trimmers?

You simply align the arrow on the knob with the eyelet. Then feed approximately 20 feet of trimmer line through the eyelet. Be sure to line up the two lengths to ensure an even feed.

How do you remove trimmer blades?

And set the screws in a safe. Place. Now loosen the two screws on the back of the blade set a quarter turn counterclockwise. Each do not completely remove these two screws with the screws loosened.

How do you open a speed feed head?

Piece right here with your hands and just turn just turn this or what you can do just hold on just hold on to the bottom part and this top piece turn.

How do you extend the cord on a strimmer?

Hold the trimmer head above the ground, press the trigger throttle and allow new line to automatically feed from the spool. Continue to hold the trigger throttle down until the line extends to the point where the blade on the trimmer guard trims it to length.

How do you change the string on a Weedeater?

Don't stand on one like I'm doing and roll. Backwards that's it and just roll. It. Right on there just like so you don't want them to cross up you just want to roll them. Right up on the reel. Now.

How long should a strimmer cord be?

The length to which the lines should be cut also varies, from around 10′ to 25′. If you are not sure, err on the side of too long; you can always cut it shorter later. Both lines should be cut to the same length. Make sure your trimmer’s engine is turned off.

Adblock
detector