Home Improvement

How do I unlock my Amana washing machine door?

Amana Front Load washer door locked at install

  1. The door may immediately unlock.
  2. The door lock LED light will blink. The door should unlock after 60 seconds. …
  3. The washer will go into a hold and drain routine for 8 minutes. After 8 minutes the door will unlock.

How do you manually unlock an Amana washer?

to the washer & remove the top panel. Reach down to the bottom of the door lock & force the release tab downwards to unlock the door.

How do you force a washing machine to unlock?


You can gently strike the door to activate the lock. However if the problem continues. You will eventually have to replace the lock. Itself.

How do I turn off the LOC on my Amana washer?

De-Activating the Control Lock:



Touch and hold 3 seconds again to de-activate the Control Lock.

How do you unlock an Amana?

Amana Oven Door is Locked – What Should I Do?

  1. Press Cancel/Off key to start a latch reset, wait 20-30 seconds and open door.
  2. Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on.

Why is my washer locked and won’t open?

The most common cause is water left in the machine. Try running a spin/drain cycle. If this fails, the machine can be drained by placing the washing machine drain hose lower than the drum (into a bucket or tray). The door interlock has simply jammed.

Why is my Amana washer stuck on lid lock?

This washer has sensors that detect the water supply and requires both hoses to have water going to the water valve. If it does not detect both water supply hoses are turned on, the control detects a problem with the water pressure sensor. The lid will lock, and the machine will enter a pump out mode for 8 minutes.

Is there a reset button on Amana washer?

Press and hold the End of Cycle or Cycle Signal button for twenty seconds. This process also reset your Amana washer and clear the flashing light.

How do you clear the codes on an Amana washing machine?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

What does E3 on Amana washer mean?

The E3 error code on an Amana washer means that the motor is experiencing a motor failure due to over current. That means the washer is trying to drive the motor but can’t sense any movement coming from it. The most likely causes are a failed motor, faulty control board, or problematic Hall Effect Sensor.

What is F4 code on Amana washer?

F4 – Open Oven Temperature Sensor – Replace oven temperature sensor.

What does f5 mean on Amana washer?

door is not locking properly

Possible Solutions



This error code indicates that the door is not locking properly.

What does E1 and F9 mean on a Amana washer?

F9 E1 Code in the display:



This error code indicates that drain times are longer than expected, typically over eight (8) minutes.

What does F1 mean on a washing machine?

The F1 fault code on this washer indicates that the water level pressure transducer signal is out of range. The pressure transducer air hose tubing being pinched or crimped can cause this. A failed pressure transducer on the machine control board can also cause it.

How do I fix F1 error?

On some models it is possible that F1 could also be caused by a keypad problem. In this case it will specify in the tech sheet to power down the oven, disconnect the keypad then power the oven back on, wait for a few minutes to see if the error reappears. If the error reappears it is definitely the control board.

How do I fix F1 error on my washing machine?

The F1 E1 alert indicates there is an issue with the appliance control unit or associated wiring. Unplug the washer, wait two minutes, then plug back in.

Adblock
detector