Regardless of the culprit, you will have to perform a reset procedure to get your furnace out of lockout. Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again.
What does it mean when your furnace says hard lockout?
Page Contents
If one of the sensors reports an unsafe condition, the furnace controller shuts off fuel and power to prevent unsafe operation. This condition is known as lockout. Your furnace will normally remain in the locked-out state until you manually reset it.
Where is the reset button on a furnace?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do you reset a furnace safety switch?
Follow these simple steps:
First, turn off the power supply to the furnace by turning off the breaker in the circuit box.
Locate the reset button on the furnace and press it to reset the furnace. …
If the button is popped up, press it down.
Return the cover to the blower compartment and turn the power on.
How long does it take for a furnace to reset?
Press and hold the reset button for about 30 seconds. Raise your thermostat to the desired temperature. This should ignite your furnace. If there’s no ignition, then it’s time to call a professional.
How many times can I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
How can the safety lockout be reset?
Regardless of the culprit, you will have to perform a reset procedure to get your furnace out of lockout. Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again.
How do I turn my furnace back on?
To do this, follow these steps:
Find the switch mounted on or near the furnace and turn the power off. …
Wait about 10 seconds.
Turn the switch or breaker back on and check the furnace to see that it has power again.
Why is there a red light blinking on my furnace?
Flashing lights could indicate that your thermostat is not sending a signal to the furnace. This problem can be caused by an issue with the wires in your walls, or it might just be that there is a loose wire connection somewhere.
Why do I need to reset my furnace?
The basic purpose of a reset button is to serve as a safety feature. It helps shut down the furnace when the furnace is too hot. This essentially prevents the overheated furnace from triggering the circuit breaker. As noted above, a furnace may need to be reset sometimes, such as when it is too hot.
Why do I have to keep pushing the reset button on my furnace?
If your furnace reset button keeps tripping, it’s most likely that your heater is overheating. This may indicate a need for heating system repair work that needs to be addressed.
What would cause my furnace to not turn on?
If your furnace is not turning on you should first check if the filter is clean. Dirty filters cause insufficient airflow and can prevent the furnace from starting. Other reasons it won’t start can stem from improper thermostat settings, forgetting to turn on the gas line, or faulty pilot light.
How do I force my furnace to start?
What would cause my furnace not to kick on?
Check your circuit breakers.
Check your thermostat settings.
Ensure your furnace filters are clean.
Check your pilot light.
Check your blower motor.
Check the furnace ignition switch.
Why is my furnace not responding to thermostat?
When a furnace is not responding to a thermostat, there is either a problem with the heating unit or the actual thermostat. Lack of power to the thermostat, wrong settings, and outdated software might be to blame, as well as faulty wiring, a tripped breaker, and a dirty furnace filter.
What do you do when your heat won’t turn on?
To troubleshoot the cause, you can do the following 10 things right now.
Check Your Thermostat. …
Inspect Your Circuit Breaker. …
Make Sure the Heating System Is On. …
Check the Pilot Light. …
Gas Supply Is Turned Off. …
Replace the Filter. …
Check the Temperature Setting. …
Check the Flame Sensor.
How do I reset my thermostat?
Here are the step-by-step reset instructions:
Turn your thermostat off by switching it to the off position.
Find the breaker that powers your HVAC system and turn it off.
Wait 30 seconds and turn the breaker back on.
Turn your thermostat back on.
Where is the ignition sensor on my furnace?
So the right side of the furnace.
How do you clean the ignition sensor on a furnace?
The Process of Cleaning a Furnace Flame Sensor
Turn off the furnace power.
Turn off the gas valve.
Remove the furnace flame sensor.
Clean the sensor with an emery cloth.
Return the flame sensor.
Restart the furnace.
What does a furnace ignitor look like?
The furnace ignitor is a small metal piece (that usually looks like two flat prongs) protected by a ceramic casing and connected to the furnace with electrical wires. It’s responsible for automatically lighting the gas that’s used to heat your home.
How much does it cost to replace a furnace flame sensor?
Flame Sensor
It stops your furnace from letting off large amounts of natural gas if it’s not working properly. If the sensor is bad, it won’t be able to sense heat and will turn the furnace off. The average cost to repair or replace a flame sensor is between $75–$200.
How do you know if furnace sensor is bad?
Furnace turns on and off down very quickly (after 2- 30 seconds). This is the classic symptom of a bad flame sensor. A faulty sensor doesn’t detect the heat that turning on a furnace makes, and subsequently closes the gas valve, shutting down the furnace. We see this as furnace short cycling in a few seconds.
Can I clean a flame sensor?
Now there's the flame sensor. And all we have to do to clean this is just to take a little piece of Emery paper. And sand it slightly. So if you don't have any of the sand. Cloth.
