Home Improvement

How do I read a Whirlpool dishwasher error code?

What do your dishwasher error codes mean?

  1. F01 — Anti-flooding overflow. …
  2. F02 — Water fill solenoid valve failure. …
  3. F03 — Water drain failure/ timeout. …
  4. F04 — Thermostat fault. …
  5. F06 — Water fill timeout. …
  6. F07 — Water turbine damaged. …
  7. F08 — Temperature timeout fault. …
  8. F09 — Software error.

How do you read a dishwasher error code?

You need to count the number of times the clean light flashes to find out the error code on your Whirlpool dishwasher. As an example: If the clean light flashes 5 times followed by 2 flashes (5-2) then this error is showing the function code = “Door issue” and the problem code is “The door switch is in question”.

How do you read a Whirlpool washer code?


The control board f06 indicates a motor speed error the control board cannot identify the motor speed check the tacho coil on the motor for continuity f08 indicates an open circuit on the heater.

How do I run the service diagnostic cycle on a Whirlpool dishwasher?

Here now is how to enter diagnostic mode on some Whirlpool dishwashers:

  1. Turn your Whirlpool dishwasher off and ensure there are no lit LED’s. …
  2. Disconnect power to your dishwasher.
  3. Reconnect power to your dishwasher and with the unit’s door open, quickly press then hold the buttons “Cycles” + “Start/Cancel” (both).

How do I clear the error code on my Whirlpool dishwasher?

Press the “Heated Dry” button, followed by pressing the “Normal” button, and then press both buttons again in quick succession. Once you’ve pressed the two buttons twice, your dishwasher should go into a diagnostic mode, which will cause it to reset. If it doesn’t work, try doing it again with the door open.

What does a flashing light on a Whirlpool dishwasher mean?

The blinking light typically indicates water heat was not detected during the cycle. You can stop the blinking and attempt to fix the problem by running a diagnostic cycle using the control panel on your dishwasher.

Why is my Whirlpool dishwasher flashing?

If the dishwasher is set for a delay start and the door is unlatched, the cycle-selected indicator lights will continuously flash and the delay countdown will stop until you latch the door. The Delay start option will run the dishwasher at a later time or during off-peak hours.

What does the Code F mean on a Whirlpool washer?

An F error code usually means the washer will not work at all, and the control board will need to be replaced.

How do I fix the error on my Whirlpool washing machine?

If the Whirlpool washer displays the de error code on display, so there are problems with a door.



Manual Review

  1. Unplug the Whirlpool washing machine from the mains.
  2. Wait for 15-20 minutes while the control unit reboots.
  3. Reset the error by pressing the START button (On/Off).
  4. Check hatch locking.


How do I find the error code on my Whirlpool Duet washer?

Duet Washer Error / Fault Codes. Once you are in the Duet Washer’s Diagnostic Mode momentarily press the 3rd button you used to enter diagnostics, and the washer will display the last 4 fault codes one button press at a time.

How do I reset my dishwasher control panel?

How Do I Reset My Dishwasher Control Panel? Simply unplug your dishwasher. Wait for one minute, then plug it back in again, to reset the dishwasher control panel.

What is the most common problem with a Whirlpool dishwasher?

A dishwasher not cleaning dishes is the most common problem. Specifically, the appliance fills with water, but the wash pump does not circulate the water or run the cycle. Mostly, this issue will occur with the failure of the wash pump or motor.

Is there a reset on a Whirlpool dishwasher?

To reset the dishwasher control panel, it needs to be disconnected from the power source for one minute. If your dishwasher is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in.

Do dishwashers have a reset button?

Can you reset your dishwasher? Yes, you can reset your dishwasher by pressing the Start/Reset button on the appliance and waiting a few minutes. If your dishwasher still doesn’t start, you may need to reboot the entire system by turning off power to the appliance at the house circuit breaker or fuse box.

What does e2 and f2 mean on a Whirlpool dishwasher?

Whirlpool gold series dishwasher error code e2 f2, means main control board is not getting correct signal from the user interface. Turn off power/breaker, remove screws holding inner door liner, remove liner and check/secure/clean all wire connections from front interface and main control board.

How do I reset the touchscreen on my Whirlpool washing machine?

In order to clear them you're gonna go over here to the spin speed button press and hold. You'll then hear it make a noise that clears all the codes.

Where is the reset button on a Whirlpool washer?

There is no Reset Button on your Whirlpool Washer. Luckily, you can reset the washer in several easy steps. If you need to reset your Whirlpool Washer and, since there is no reset button, first unplug the washer. After two minutes, plug the washer back in.

Is there a reset button on a Whirlpool washer?

Steps to Reset a Whirlpool Washing Machine



The following steps should be used to reset your Whirlpool washing machine: Turn off the washer. Turn the mode dial to NORMAL. Turn the dial counter-clockwise one click left, clockwise three clicks, counterclockwise one click, and then clockwise one click.

How do I reset my washer?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do you reset a dishwasher?

So what you're gonna do is push high temp wash and heat it dry and you know to push them simultaneously. Just like this. So high temp heat it tight temp heat it. That's gonna put you into.

What does resetting a washer do?

A reset feature in newer washing machines allows you to restart the machine after it experiences an error or fault. Power spikes, imbalanced loads or an interruption in power are some of the causes of these problems. You can reset the machine’s motor by pressing a button.

Adblock
detector